Design and optimization of a cavitating device for Congo red decolorization: Experimental investigation and CFD simulation

The aim of this work is to perform design and optimization of a cavitating device based on CFD simulation. A set of operational and geometrical parameters such as convergence angle, divergence angle, length of throat, and inlet pressure that can affect the hydrodynamic cavitation phenomenon generating in a Venturi are evaluated through CFD simulation and experimental approaches. Response surface methodology (RSM) was employed to achieve the optimum geometrical configuration. The CFD results show that the maximum cavitation zone in the Venturi can be obtained when half angle of the convergence section, throat length and half angle of the divergence section are 22.7°, 4 mm, and 6.5°, respectively. A maximum decolorization of 38.8% has been obtained using the designed Venturi at cavitation number (Cv) of 0.12. Additionally, the results were compared to that of various orifice plates. A decolorization of 26.2% using 33 holes orifice plate and 11.55% in one hole orifice plate approved the superiority of the designed Venturi.     

An Insight into the Diffusion of Unsaturated Polyester (UP) Resin into Expanded Graphite (EG) to Improve the Mechanical Properties of the UP/EG Composites

Abstract

Polymer/expanded graphite (EG) nanocomposites have great importance in many industrial applications mainly due to their high electrical/thermal conductivity or flame retardancy. However, to fully employ the benefits of polymer/EG nanocomposites one must consider the high degree of porosity of EG. The high degree of porosity of EG can deteriorate the composites’ mechanical properties if the polymer chains cannot diffuse completely into the EG pores. In this article, an insight is given into the diffusion of unsaturated isophthalic polyester (UP) resin, consisting of a combination of maleic anhydride and isophthalic anhydride in the resin backbone, with two viscosities, into the pores of the EG particles of various degrees of porosity. The diffusion experiments were carried out on compressed EG tablets with the same density but different porosity due to the different porosity of the EG particles. The results showed that the diffusion rate of the UP resin with higher viscosity slightly decreased when the EG porosity decreased but, in the opposite way, it strongly increased for the low viscosity UP resin. The EG nanocomposites samples were molded at varying pressures. The micrographs of the fractured surfaces of the EG nanocomposites showed that the EG pores were not filled with resin, thus the EG nanocomposites had residual pores. It was found that composites containing EGs with higher expansion ratio and larger particles and pores showed larger residual pores. Furthermore, the composites prepared with the more viscous UP resin showed more residual pores. By applying a pressure of 10?bar instead of 1?bar, a reduction of 7–20% in the residual pores of the nanocomposites was observed which led to improved mechanical properties by up to 20% in flexural strength for the EG with the highest expansion ratio.     

砂岩方梁断裂过程区范围的实验确定方法

裂纹前端的断裂过程区是引起岩石非线性断裂及尺寸效应的主要原因。利用数字图像相关技术对砂岩开展了三点弯曲梁实验,获得观测区域高精度的全场位移和应变数据,根据断裂韧带区域水平位移和水平应变的分布特征,结合裂尖岩石颗粒变化的微观分析,提出采用裂纹尖端水平位移波动性和水平应变突变性所得到的波动系数和水平应变突变值,确定断裂过程区形状和临界尺寸的方法。结果表明:砂岩断裂过程区的形状为不规则的狭长带状区域,断裂过程区的临界长度为11~13mm,临界宽度为1.58~2.36mm。断裂过程区区域内形变在趋向裂尖时呈指数增加,但其单位区域内的形变增量呈波动状态。该方法能够更加准确判断岩石断裂过程区的范围,有助于分析岩石的非线性断裂特性。     

Capillary electrophoresis and ultra-high-performance liquid chromatography methods in clinical monitoring of creatinine in human urine: A comparative study

Creatinine is an important diagnostic marker and is also used as a standardization tool for the quantitative evaluation of exogenous/endogenous substances in urine. This study aimed at evaluating and comparing three analytical approaches, based on hyphenations of different separation [two-dimensional capillary isotachophoresis (CITP–CITP), capillary zone electrophoresis (CZE), ultra-high-performance liquid chromatography (UHPLC)] and detection [conductivity (CD), ultraviolet (UV), tandem mass spectrometry (MS/MS)] techniques, for their ability to provide reliable clinical data along with their suitability for the routine clinical use (cost, simplicity, sample throughput). The developed UHPLC–MS/MS, CITP–CITP–CD, and CZE–UV methods were characterized by favorable performance parameters, such as linearity (r ˃ 0.99), precision (relative standard deviation, 0.22–2.97% for the creatinine position in analytical profiles), and recovery (87.1–115.1%). Clinical data, obtained from the analysis of 24 human urine samples by a reference enzymatic method, were comparable with those obtained by the tested methods (Passing–Bablok regression and Bland–Altman analysis), approving their usefulness for the routine clinical use. In this context, the UHPLC–MS/MS method provides benefits of enhanced orthogonality/accuracy and high sample throughput (threefold shorter total analysis times than the CE methods), whereas advantages of the CE methods for routine labs are simplicity and low cost of both the instrumentation and measurements.     

利用电磁法研究HMX与TATB混合钝感炸药的冲击起爆特性

为研究含有少量奥克托金(HMX)且以三氨基三硝基苯(TATB)为基的高能钝感炸药PBX-3的冲击起爆反应增长规律,采用火炮驱动蓝宝石飞片的方法和铝基组合式电磁粒子速度计技术进行了一维平面冲击实验。通过实验测量撞击表面及内部不同深度处的冲击波后粒子速度,得到PBX-3炸药的Hugoniot关系。根据冲击波示踪器所测数据绘制了炸药到爆轰的时间-距离(x-t)图,获得了反映炸药冲击起爆性能的Pop关系。将入射压力为12.964 GPa时达到爆轰的6条速度曲线修整成相同零点,通过读取6条曲线的分离点即反应区末端的C-J点,计算出化学反应区时间和宽度。     

Palladium‐catalyzed decarboxylative coupling of α,β‐unsaturated carboxylic acids with aryl tosylates

We report a general method for selective cross‐coupling of α,β‐unsaturated carboxylic acids with aryl tosylates enabled by versatile Pd(II) complexes. This method features the general cross‐coupling of ubiquitous α,β‐unsaturated carboxylic acids by decarboxylation. The transformation is characterized by its operational simplicity, the use of inexpensive, air‐stable Pd(II) catalysts, scalability and wide substrate scope. The reaction proceeds with high trans selectivity to furnish valuable (E)‐1,2‐diarylethenes.     

A Switch in the Hydrophobic/Hydrophilic Gas-Adsorption Character of Prussian Blue Analogues: An Affinity Control for Smart Gas Sorption

Porous coordination polymers are molecule-based materials presenting a high degree of tunability, which offer many advantages for targeted applications over conventional inorganic materials. This work demonstrates that the hydrophilic/hydrophobic character of Prussian blue analogues having a lipophilic feature may be tuned to optimize the gas adsorption properties. The role of the coordinatively unsaturated metal sites is emphasized through a combination of theoretical and experimental study of water, ethanol, and n-hexane adsorption.     

A unified theory for brittle and ductile shear mode fracture

A unified theory captures both brittle and ductile fracture. The fracture toughness is proportional to the applied stress squared and the length of the crack. For purely brittle solids, this criterion is equivalent to Griffith's theory. In other cases, it provides a theoretical basis for the Irwin-Orowan formula. For purely ductile solids, the theory makes direct contact with the Bilby-Cottrell-Swinden model. The toughness is highest in ductile materials because the shielding dislocations in the plastic zone provide additional resistance to crack growth. This resistance is the force opposing dislocation motion, and the Peach-Koehler force overcomes it. A dislocation-free zone separates the plastic zone from and the tip of the crack. The dislocation-free zone is finite because molecular forces responsible for the cohesion of the surfaces near the crack tip are not negligible. At the point of crack growth, the length of the dislocation-free zone is constant and the shielding dislocations advance in concert. As in Griffith's theory, the crack is in unstable equilibrium. The theory shows that a dimensionless variable controls the elastoplastic behaviour. A relationship for the size of the dislocation-free zone is derived in terms of the macroscopic and microscopic parameters that govern the fracture.     

Determination of sulfa antibiotic residues in river and particulate matter by field-amplified sample injection-capillary zone electrophoresis

In the present research, field-amplified sample injection–CZE (FASI–CZE) coupled with a diode array detector was established to determine trace level sulfa antibiotic. Sulfathiazole, sulfadiazine, sulfamethazine, sulfadimethoxine, sulfamethoxazole, and sulfisoxazole were selected as analytes for the experiments. The background electrolyte solution consisted of 70.0 mmol/L borax and 60.0 mmol/L boric acid (including 10% methanol, pH 9.1). The plug was 2.5 mmol/L borax, which was injected into the capillary at a pressure of 0.5 psi for 5 s. Then the sample was injected into the capillary at an injection voltage of –10 kV for 20 s. The electrophoretic separation was carried out under a voltage of +19 kV. The capillary temperature was maintained at 20˚C throughout the analysis, and six sulfonamides were completely separated within 35 min. Compared with pressure injection-CZE, the sensitivity of FASI-CZE was increased by 6.25–10.0 times, and the LODs were reduced from 0.2–0.5 to 0.02–0.05 μg/mL. The method was applied to the determination of sulfonamides in river water and particulate matter samples. The recoveries were 78.59–106.59%. The intraday and interday precisions were 2.89–7.35% and 2.77–7.09%, respectively. This provides a simpler and faster method for the analysis of sulfa antibiotic residues in environmental samples.